INTRODUCING IONFPV P4 LITE IN DEVELOPMENT

Open-source HD video for your next build.

A digital FPV video transmitter with a camera for about €50. 720p at up to 90 fps, latency from 40 ms, range up to 2 km, and on-board recording. Watch with a €20 Wi-Fi adapter on your PC, phone or Raspberry Pi.

Rendering of the IONFPV P4 Lite V0.1 board, a square black circuit board with the IONFPV logo, a central processor, a USB-C port and two white connectors
ESP32-P4 + ESP32-C5Rendering of the P4 Lite V0.1 board designSCROLL TO EXPLORE
720p / 90 fps

Race mode

40 ms

Latency measured in race mode

~€50

VTX with camera, target price

Open source

Hardware. Firmware. Software.

THE IONFPV P4 LITE

Open technology.
New possibilities.

An ESP32-P4 video transmitter that puts the freedom to build at the heart of FPV. Designed around HD video, low latency, an approachable cost, and a receiver that uses a €20 Wi-Fi adapter and the screens you already own.

01 / THE PLATFORM
Rendering of the underside of the IONFPV P4 Lite board, showing a large shielded module with an antenna connector and a ribbon-cable connector
IONFPV P4 Lite V0.1 · rendering of the board's underside

A capable core.
An open direction.

An ESP32-P4 for video and an ESP32-C5 for an adaptive 2.4–5.8 GHz link, drawing under 3 W and recording to an on-board SD card.

02 / THE VIDEO
HDYOUR VIEW, IN DETAIL

Choose your perspective.

Race mode at 720p and 90 fps for low latency, 720p at 60 fps for smooth motion, or cinema mode at 1080p and 30 fps for detail.

Explore video modes
03 / THE FREEDOM

Built to be understood.

The open-source goal: hardware, firmware, and receiver software you can explore and adapt.

About open development

HARDWARE IN FOCUS

The P4 Lite,
up close.

A standard 36 × 36 mm board with an ESP32-P4 for video and an ESP32-C5 for a dual-band radio link, drawing under 3 W.

The board shown is the V0.1 prototype design. Weight and input voltage will be published with V1.0, and details may change before release.
Rendering of the whole IONFPV P4 Lite V0.1 board, showing the processor, the USB-C port, two white connectors and the four mounting holes
IONFPV P4 LITE / V0.1 BOARD · RENDERING

Video

Modes
720p at 90 fpsRace mode
720p at 60 fpsSmooth
1080p at 30 fpsCinema mode
Latency
From 40 msRace mode, measured
Recording
On-board SD card

Radio

Link
2.4 and 5.8 GHzAdaptive
Range
2 kmStandard, CE
6 kmLong range
20 kmFCC mode, planned
Receive with
€20 Wi-Fi adapterRTL8812AU or similar

Camera

Sensor
5 MPOV5647
12 MPIMX708
Field of view
120° or 140°Wide angle

Board

Processors
ESP32-P4Video
ESP32-C5Radio
Size
36 × 36 mm30.5 mm mounting
Power
Under 3 W
Connectors
USB-C
U.FLAntenna
Price
About €50With basic camera

THE VIDEO EXPERIENCE

Every frame.
A little more freedom.

Choose the mode that fits the way you fly, from low-latency racing to full HD detail.

Illustrative aerial alpine scenery showing the type of view FPV makes possible
720p / 90 fpsILLUSTRATIVE VIEW

EXPLORE THE VIDEO MODES

RACE MODE · LOW LATENCY
720p
90FPS

The fastest mode, built for racing. Latency measured as low as 40 ms on prototypes.

Resolution1280 × 720
Frame interval11.1 ms

Race-mode latency was measured on prototypes; the other modes are development targets. Frame interval is the time between frames, not end-to-end latency. Illustrative image, not IONFPV footage.

MAKE ROOM FOR THE NEXT IDEA

Big possibilities.
Approachable hardware.

Digital FPV should leave space in your budget to keep experimenting. The P4 Lite with its basic camera targets about €50. To watch, add a USB Wi-Fi adapter such as the RTL8812AU for about €20, and use the PC, phone or Raspberry Pi you already have.

See development details
TARGET PRICE, VTX + CAMERA~€50

A development goal.
More room to build.

VTX with the basic camera. The IONFPV receiver is a separate product. Final pricing to be confirmed.

HOW IT COMPARES

A different kind
of digital FPV.

Analog is affordable. Closed HD systems look great. IONFPV aims for HD video you can afford, understand, and watch with a €20 adapter on the screens you already own.

The P4 Lite compared with analog and closed digital HD FPV systems
AnalogClosed digital HDIONFPV P4 Lite
ImageDrawback:Standard definitionAdvantage:HDAdvantage:HD, 720p90 race mode or 1080p30 cinema mode
LatencyAdvantage:Very lowAdvantage:LowNeutral:As low as 40 ms in race mode
RecordingNeutral:In the goggles, standard definitionAdvantage:On boardAdvantage:On-board SD card
Where you watchNeutral:Analog goggles or monitorDrawback:Mainly the maker's own gogglesAdvantage:PC, phone, tablet or Raspberry Pi. HDMI goggles with the IONFPV receiver.
Receiving hardwareAdvantage:Low-cost analog receiverDrawback:The maker's goggles, usually the biggest costAdvantage:A USB Wi-Fi adapter for about €20
OpennessNeutral:Common analog standardDrawback:Closed hardware and firmwareAdvantage:Open hardware, firmware and software
Transmitter costAdvantage:LowDrawback:HigherAdvantage:About €50 with a camera, target

Analog and closed digital HD are described in general terms, such as DJI and Walksnail systems; individual products vary. IONFPV values are development targets, except the latency, which was measured on prototypes.

THE RECEIVER, REIMAGINED

A €20 adapter.
The screen you already own.

Receive the video with a USB Wi-Fi adapter such as the RTL8812AU, which costs about €20, and watch it in the IONFPV app on your PC, phone, tablet or Raspberry Pi. For goggles, the IONFPV receiver is a standalone product made to work hand in hand with the P4 Lite. It has its own antennas, decodes the video itself, and outputs it over HDMI.

  1. 01ON YOUR DRONE

    Camera + P4 Lite

    Records to the SD card and sends your video over the adaptive 2.4–5.8 GHz link.

  2. 02AT YOUR RECEIVER

    Wi-Fi adapter

    A USB adapter such as the RTL8812AU, or the IONFPV receiver, which decodes the video itself.

  3. 03ON YOUR SCREEN

    IONFPV app or HDMI

    The app on PC, phone, tablet or Raspberry Pi, or goggles connected to the receiver.

WAYS TO WATCH

Your screen.
Your setup.

A big screen for setup and spectators.

Plug a USB Wi-Fi adapter such as the RTL8812AU into your PC and open the IONFPV app to see the live view.

Adapters based on the RTL8812AU and similar chips are supported. A list of tested adapters and devices, with setup guides, will be published with V1.0.

YOUR NEXT DRONE PROJECT

From the workbench.
To a new view.

Setup is meant to be simple. Documentation will cover cameras, transmitter installation, Wi-Fi adapters, and every way to watch.

Illustrative hobby FPV quadcopter on a carry case in alpine scenery
Built around the joy of making and flying. Illustrative image.
01

Choose your setup.

Pick your camera and lens, and how you want to watch, from a phone with a Wi-Fi adapter to HDMI goggles with the IONFPV receiver.

02

Install the P4 Lite.

Connect the transmitter to your camera and drone using the project’s wiring, power, and mounting guidance.

03

Bring up your view.

Plug the Wi-Fi adapter into your device and open the IONFPV app, or connect the receiver over HDMI. Check the complete video link on the bench before flying.

ABOUT IONFPV

Built for people
who build.

We believe the most interesting flight is the one you make your own.

IONFPV is developing an open-source first-person video system for drone hobbyists and electronics enthusiasts. Our focus is an accessible transmitter, flexible receiver software, and a clear path from curiosity to a working project.

The P4 Lite is where that idea begins: open technology, practical experimentation, and the freedom to understand what’s inside your build.

Illustrative scene of a hobby builder assembling a quadcopter at a workbench
From an idea to a working build. Illustrative workshop scene.
01

Accessible by design.

An approachable cost target and familiar receiver hardware.

02

Open at the core.

A project you can understand, explore, and adapt.

03

Made for enthusiasts.

Built around the curiosity that gets a new project off the bench.

BEHIND THE PROJECT

One vision.
Every part matters.

The work behind IONFPV connects the transmitter, the receiving application, and the guidance that helps enthusiasts put them together.

H / 01

Hardware
& firmware

The ESP32-P4-based transmitter platform and the firmware that brings the video path together.

S / 02

Receiver
& app

The IONFPV app for PC, phones, tablets and Raspberry Pi, and the IONFPV receiver.

D / 03

Documentation
& integration

Supported parts, setup guidance, and the details builders need to understand their system.

DEVELOPMENT PROGRESS

Where the project
is today.

We share progress as it happens. Sign up for updates to hear when each step is ready.

  1. Done

    Board design

    Schematic and layout of the P4 Lite V0.1 board.

  2. Done

    First prototypes

    V0.1 boards sending video, with 40 ms latency measured in race mode.

  3. In progress

    IONFPV app

    The app for PC, phones, tablets and Raspberry Pi, with RTL8812AU-based adapters.

  4. Planned

    FCC mode

    A transmitter mode for FCC regions, for range up to about 20 km.

  5. Planned

    V1.0 launch

    The P4 Lite with a choice of camera and lens, plus setup guides and open source code.

  6. Planned

    V2 with 4K

    A new product with 4K streaming, after V1.0.

IONFPV receiverA standalone product, made to pair with the P4 Lite
  1. In progress

    Receiver design

    Antennas, video decoding and HDMI output in one unit.

  2. Planned

    Receiver prototypes

    Build and test the first receivers with goggles and monitors.

  3. Planned

    Receiver launch

    Available on its own, for pilots who fly with HDMI goggles or monitors.

OPEN DEVELOPMENT

Make it.
Understand it.
Make it your own.

The project starts in the open.

The GitHub repository will live here. Source code, documentation, and contribution details will be linked when they’re ready.

HardwareFirmwareReceiver app

DEVELOPMENT DETAILS

A clear view
of what’s next.

IONFPV is in development.
Here’s what the current targets mean.

Is IONFPV available yet?

Not yet. The P4 Lite, the app and the receiver are in development, and the price and platform support on this page are targets. Release timing has not been announced. Sign up for updates to hear first.

What does the ~€50 target cover?

The P4 Lite transmitter with the basic camera. It is a target price, not a current sale price. To watch, you also need a USB Wi-Fi adapter, which costs about €20, or the IONFPV receiver, which is sold separately.

What do I need to receive the video?

A USB Wi-Fi adapter based on the RTL8812AU or a similar chip, connected to a PC, an Android phone or tablet, or a Raspberry Pi running the IONFPV app. iPhone and iPad can't connect to the adapter directly, so the IONFPV receiver or a nearby computer receives the video and restreams it to them over Wi-Fi. A list of tested adapters will be published with V1.0.

Can I use FPV goggles?

Yes, with the IONFPV receiver, a standalone product made to pair with the P4 Lite. It decodes the video itself, and goggles with an HDMI input connect to it directly. It is in development.

What about latency and range?

In race mode, at 720p and 90 fps, we have measured latency as low as 40 ms on prototypes. Range is about 2 km in the standard CE mode, about 6 km in the long-range, low-bitrate mode, and about 20 km in the planned FCC mode.

Which cameras can I use?

The P4 Lite will be sold with a choice of two cameras, the 5 MP OV5647 or the 12 MP IMX708, each with a 120° or 140° wide-angle lens.

Which radio band does it use, and is it legal where I fly?

The P4 Lite uses an ESP32-C5 for an adaptive link across 2.4 GHz and 5.8 GHz. The standard mode follows CE limits, and an FCC mode for the transmitter is on the roadmap. Radio rules differ by country, so check your local regulations before flying.

Will there be 4K?

Yes, in a new product. After V1.0 of the P4 Lite, V2 will add 4K streaming.

STAY IN THE LOOP

Follow the build.
Hear it first.

Get an email when the receiver is ready, the source goes public and V1.0 launches. Only IONFPV news, a few times a year.

We only use your email to send IONFPV updates. Sign-up is handled by Buttondown, and you can unsubscribe at any time.